ControllerCheckup

Switch Pro Controller tester

  • Nintendo
  • USB or Bluetooth
  • Chrome, Edge, Firefox, Safari
  • Nothing to install

Test a Nintendo Switch Pro Controller on your computer or phone: every button with Nintendo's names, both sticks with a 10-second drift check, and ZL and ZR.

No Pro Controller found yet. Connect it, then press any button.

Left stick

X
0.000
Y
0.000
From centre
0.0%

Buttons

Press any button

Right stick

X
0.000
Y
0.000
From centre
0.0%

Drift check

Put the controller down, take your hands off it, then start the check.

Triggers and vibration

LT
0%
RT
0%

Vibration needs Chrome, Edge or Opera, and a controller that reports its motors to the browser.

Every axis

Raw values from -1 to 1. A resting stick should sit close to 0.

Controller details

Name
–
Button names
–
Layout
–
Buttons / axes
–
USB IDs
–
Updates seen
–

Checklist 0 buttons tested

Waiting for your Pro Controller

  1. Connect your Pro Controller with a USB cable, or pair it over Bluetooth in your computer's or phone's settings.
  2. Press any button on it. Browsers only show a controller to a page after a button press.
  3. Nothing happens? Try another USB cable (some only charge), or open this page in Chrome or Edge.

How to test a Switch Pro Controller

  1. Connect it with a USB-C data cable, or pair it over Bluetooth: hold the small sync button on top until the player lights run back and forth, then pick "Pro Controller" in your Bluetooth settings.
  2. Press any button so the page can see it. Chrome and Edge show Nintendo's button names (B, A, Y, X, ZL, ZR, Minus, Plus, Home, Capture).
  3. Press every button until the checklist is green and roll both sticks round the edge.
  4. Run the drift check with the controller lying flat.

Nintendo's B and A sit where Xbox has A and B. This page names them as Nintendo does, so the bottom button is B. If a game on your PC swaps them, the button mapping test shows exactly how your computer sees each one.

What your results mean

ReadingHealthyWorth a look
Stick at rest (drift check)Under 5% from centreOver 5%: raise the game's deadzone; over 10%: calibrate or repair
Trigger travelRuns smoothly from 0% to 100%Stops short of 100%, jumps, or doesn't return to 0%
ButtonsEach tile lights once per pressA tile that won't light, flickers, or lights without a press
Every axisResting axes sit close to 0.00An axis that creeps or jitters while nobody touches it

Common Pro Controller problems

  • Drift: less common than on Joy-Con, but it happens. A drift reading over 5% is worth fixing with the Switch's own stick calibration (System Settings, Controllers and Sensors).
  • Not detected over USB on Windows: close Steam, which can take over Nintendo controllers, and try Bluetooth.
  • Rumble: the Pro Controller's HD Rumble isn't available to most browsers, so the vibration buttons may do nothing. That doesn't mean the motors are broken.

Switch 2 Pro Controller

The Switch 2 Pro Controller connects the same way. Browsers that don't yet recognise its layout show its buttons by number; the checklist still confirms every button works.

Questions

How do I pair a Switch Pro Controller with my PC?

Hold the sync button on top until the lights scroll, then choose "Pro Controller" in your computer's Bluetooth settings. Or just use a USB-C data cable.

Why is A and B swapped?

Nintendo puts B at the bottom and A on the right. This page uses Nintendo's names. PC games often use Xbox positions, so check your game's settings.

Can I test HD Rumble?

Most browsers can't send rumble to a Pro Controller, so a silent vibration test here doesn't mean the motors are faulty.

How do I fix Pro Controller drift?

Recalibrate on the Switch (System Settings, Controllers and Sensors, Calibrate Control Sticks), then test again here. If the reading stays high, the stick needs repair.

Does it test the motion sensors?

No. Browsers don't read the Pro Controller's gyro.