ControllerCheckup

PS5 controller stick calibration

Recalibrate the centre and outer range of your DualSense sticks over USB, test the result, and only then save it. Often fixes drift and sticks that can't reach full tilt.

No controller connected yet.

Your sticks now

LeftRight
Drift at rest––
Before calibrating––
Range covered––

Calibrate

  1. Check the controller

    Confirms it's a genuine DualSense or DualSense Edge on a USB cable with current firmware. Nothing is changed.

  2. Centre

    Put the controller down flat and let go of both sticks completely.

  3. Range

    Press start, then roll both sticks slowly around their outer edge, pressing firmly against the rim, until both rings are complete.

  4. Keep it

    Your new calibration works now, but it's temporary: unplugging or turning off the controller undoes it. Test it in the stick drift test first, then save it.

Connect your controller with a USB cable and press Connect controller.

Waiting for your controller

  1. Connect your DualSense with a USB-C data cable, or pair it over Bluetooth.
  2. Press Connect controller and choose it in the box that opens.
  3. This test talks to the controller directly, so it needs Chrome, Edge or Opera on a computer.

Before you start

  • Use Chrome, Edge or Opera on a computer, and connect the controller with a USB-C data cable. Calibration doesn't work over Bluetooth.
  • Run the stick drift test and the circularity test first, so you know where you're starting from.
  • Calibration can't fix a stick that is physically worn or dirty. If drift comes back within days, the stick module needs cleaning or replacing.

How to calibrate your sticks

  1. Press Connect controller and choose your DualSense or DualSense Edge.
  2. Press Check my controller. The page makes sure it's a genuine controller with current firmware. Nothing is changed.
  3. Tick the box, put the controller down flat, let go of the sticks and press Calibrate centre.
  4. Press Start range calibration and roll both sticks slowly around their outer edge until both rings are complete, then press Finish range.
  5. Test your sticks. The new calibration is temporary: unplugging the controller undoes it. If you're happy, press Save permanently.

What calibration does

Each stick reports its position as numbers. The controller stores where "centre" and "fully pushed" are for each stick, and uses those to work out what games see. Over time, or after a stick is replaced, those stored values can be slightly off: the stick reads a little away from centre when you let go (drift), or can't reach full tilt in some directions. Calibration measures your sticks now and stores fresh values.

ProblemWill calibration help?
Small, steady drift in one directionOften, yes.
Stick can't reach full tilt one wayOften, yes (range calibration).
Replacement Hall effect or TMR stick feels unevenUsually, yes. Replacement sticks often need calibrating after fitting.
Drift that jumps around or changes with temperatureRarely. The stick module is worn; it needs cleaning or replacing.

Safety

The page only calibrates controllers that report genuine firmware details and an up-to-date firmware version, and refuses copies, Bluetooth connections and old firmware. The new values are temporary until you choose to save them, so if anything looks wrong, unplug the controller and it goes back to how it was. On the DualSense Edge, calibration is stored inside each stick module, which Sony write-protects, so it lasts until the controller is unplugged.

The calibration steps follow the open-source DualShock Calibration GUI project, which has been used on a very large number of controllers. As with any tool that changes settings on a device, you use it at your own risk.

Questions

Can stick calibration fix drift?

It fixes drift caused by the controller's stored centre being slightly off. It can't fix a worn or dirty stick, which needs cleaning or replacing.

Is it safe for my controller?

The new calibration is temporary until you press Save permanently, so you can test it first and unplug the controller to undo it. The page also refuses copies and old firmware.

Why does it need a USB cable?

The calibration commands only work over USB. Over Bluetooth the controller doesn't accept them.

Does it work on the DualSense Edge?

Yes, but only until the controller is unplugged: the Edge stores calibration inside each stick module, and saving it there permanently isn't available on this site yet.

Will the calibration work on my PS5?

Yes. Once saved, the calibration is stored in the controller, so it applies on PS5, PC and everywhere else.

How do I undo a saved calibration?

Run the calibration again with the sticks untouched and fully rolled. That stores fresh values in place of the old ones.